UP 7DSP 7-channel amplifier with DSP

Match
Your price:
€ 749,00
Price per single item (VAT included)
Available on backorder

Information and details

Calculating shipping costs to
Amplifier Type
7 channels
Amplifier Class
H
RMS Power 4 Ohm
5x65 + 2x160 Watt
RMS Power 2 Ohm
5x130 + 2x320 Watt
Total Harmonic Distortion
0,03 % THD
S/PDIF Digital Input
No
High Level Input
YES
Crossover
Yes
MAX Power Consumption
500 Ampere
Size
153 x 130 x 46 mm

UP 7DSP is the most powerful MATCH DSP amplifier and includes the new ADEP.3 circuits. It offers seven channels of amplification in total and an additional pre-amplified output, which allows, in combination with its integrated 8-channel DSP, to perfectly drive individual and complex speaker configurations. Two of the output channels deliver 160 Watts RMS at 2 Ohm - enough to power subwoofers.

Power combined with "intelligent control" which is why UP 7DSP incorporates a powerful latest generation 64-bit DSP, which enables revolutionary and proprietary new features such as "Augmented Bass Processing", the "StageXpander" or the "RealCenter" function.

But that's not enough: simply enjoy music from your smartphone with unprecedented quality. UP 7DSP is equipped with a MATCH expansion card slot (MEC) for additional input and output interfaces such as the Bluetooth audio streaming module or a high-resolution USB audio card.

Thanks to the professional and intuitive DSP PC-Tool V4 software, the configuration and installation of UP 7DSP are rather simple and intuitive.

Strengths of the Match UP 7DSP:

HD Class Technology
UP 7DSP combines the advantages of a class H technology with the principle of a class D amplifier. The result is unmatched efficiency that easily surpasses any conventional class D amplifier. By varying the internal supply voltage based on the amplitude of the amplifier input signals, idle losses are significantly reduced and overall efficiency is nearly at maximum at any time.

Intelligent High-Level Input ADEP.3
Modern factory-installed car stereos incorporate sophisticated diagnostic capabilities of connected speakers. In particular, the latest generation car stereos are equipped with additional monitoring functions so that error messages and loss of specific functions (e.g. fader function) appear quite often if an amplifier will be connected, but not with UP 7DSP.
The new ADEP.3 circuit (Advanced Diagnostics Error Protection, 3rd generation) avoids all these problems without unnecessarily loading the OE radio speaker outputs when high volumes are present.

Start-Stop Functionality
The switched power supply of MATCH UP 7DSP ensures a constant internal supply voltage even if the battery voltage drops to 6 Volts during engine start. If the supply voltage drops below 10.5 Volts for more than five seconds, the amplifier switches to "protection mode" (the status LED lights up red) to prevent any further discharge of the car battery.

Automatic Digital Signal Detection
The switch from analog input to digital input is performed automatically as soon as a signal is detected on the optical input. This function can be disabled in the DSP PC-Tool software. Alternatively, an optional remote control can be used for manual switching between analog and digital inputs.

Power Saving Mode
Power saving mode is integrated in the basic configuration. It allows you to significantly reduce the power consumption of the UP 7DSP and potentially connected amplifiers when there is no input signal for more than 60 seconds. Note that in many cars updated with "CAN" or any other internal bus structure it can happen that the radio remains "invisibly" on for up to 45 minutes even after closing and leaving the car! Once "Power Saving Mode" is activated, the remote output and therefore the connected amplifiers will be switched off. MATCH UP 7DSP will reactivate the remote output within one second if a music signal is applied. The shutdown time of 60 sec. can be changed or the "Power Saving Mode" can be completely disabled via the DSP PC-Tool software.

Scheda tecnica

n-20200323161330-ba-up-7dsp.pdf

Match UP 7DSP technical features

RMS output power / max.
- @ 4 Ohm 5 x 65/130 Watts (front / rear / center channels)
- Subwoofer output @ 2 Ohm 2 x 160/320 Watts
Amplification technology HD Class
Inputs 4 x high-level speaker input
1 x SPDIF optical (12 - 96 kHz)
1 x MEC
1 x Remote input
Input sensitivity High-level 5 - 11 Volts
RCA / Cinch input impedance -
High-level input impedance 13 Ohm
Outputs 7 x Speaker output
1 x RCA / Cinch
2 x Remote output
RCA / Cinch output voltage 3 Volts RMS
Frequency response 20 Hz - 22,000 Hz
DSP resolution 64 bit
DSP power 295 MHz (1.2 billion MAC operations / second)
Sampling frequency 48 kHz
Audio signal processor type DSP
Signal converters A / D: BurrBrown D / A: BurrBrown
Digital input signal-to-noise ratio 105 dB (A-weighted)
Analog input signal-to-noise ratio 103 dB (A-weighted)
Distortion (THD) <0.03%
Damping factor > 100
Operating voltage 10.5 - 16 Volts (max. 5 sec. down to 6 Volts)
Idle current 450 mA
Max. remote output current 500 mA
Fuse 2 x 25 A LP-Mini-fuse (APS)
Additional features HD class technology with dynamic power control, ADEP.3 circuit, Start-Stop capability, control input, USB, MEC slot, Auto Remote switch, galvanically isolated Line Out
Dimensions (H x W x D) 46 x 130 x 153 mm / 1.81 x 5.12 x 6.02 "

€ 749,00 Price incl. VAT